Délai de livraison moyen 2 à 3 jours
Fostex Moniteur rack 19" 2x10W 2 entrées XLR/combo + 1 Dante
1 year warranty
- Built-In Rectangular Stereo Speakers
- Onboard Amplifier (10W per Channel)
- Dante Digital Input via RJ45
- Balanced Analog Inputs via XLR
- Balanced Analog Outputs via XLR
- 1/4" Stereo Headphone Jack
- Supports Sample Rates up to 96 kHz
- 26-Dot LED Meters
- Power-Saving Design
- Occupies 1 RU of Rack Space
Fostex Moniteur rack 19" 2x10W 2 entrées XLR/combo + 1 Dante
- Fostex RM-3DT Rackmount Active Monitor Speaker
- Power Cable
- 4 x Rubber Feet
Fostex RM-3DT Rackmount Active Monitor Speaker
Designed to fit the monitoring needs of space-challenged environments like machine rooms, surveillance operations, and mobile or stationary control rooms, the Fostex RM-3DT is a Dante-equipped active monitor speaker that occupies just 1 RU of rack space. It can accept digital signal over a Dante network or a stereo analog source via balanced XLR inputs, ensuring compatibility with a wide range of systems. Signal can be output in one of four modes to the built-in rectangular stereo speakers, while the balanced XLR output jacks act as a thru-put to send the analog input to another destination. The front-panel 1/4" headphone jack allows for personal monitoring without pushing sound through the speakers.
Left and right 26-dot LED meters give you a visual representation of your levels. The volume control also functions as a mute switch, which can be programmed for total mute, or to provide a 20 dB attenuation based on your preference. The RM-3DT supports sample rates up to 96 kHz and features a power-saving design that keeps its power consumption down to just 10W. Sporting the same dimensions as the non-Dante RM-3, the RM-3DT can be conveniently swapped in its place.
Analog and Digital Inputs
Accepts balanced analog sources via two XLR 3-pin female inputs and Dante signal via an RJ45 female input
Built-In Speakers
Outputs either or both of any 2-channel digital signals extracted from Dante network signals to built-in rectangular speakers, each powered by 10W of onboard amplification
Line and Headphone Outputs
Two XLR balanced analog outputs on the rear panel and one 1/4" stereo headphone jack on the front
High-Resolution Audio
Supports sample rates up to 96 kHz
Dual LED Meters
Dual 26-dot LED meters indicate either VU, VU + Peak, VU + Peak Hold, or Peak + Peak Hold
Adjustable Brightness
Display brightness can be adjusted in four levels
Low Power Consumption
Digital amplifier and switching power supply yield a power-saving design
Rackmount Form Factor
Physical dimensions are identical to the conventional RM-3 for easy replacement
- Built-In Speakers : 4.3 x 1.6" / 11 x 4 cm Rectangle Cone Speakers
- Impedance : 8 Ohms
- SPL : 84 dB/W (1 m)
- Frequency Response : 200 Hz to 20 kHz
- Maximum Output : 10 W x 2
- Residual Noise : -50 dBV or Less (DIN AUDIO)
- Distortion : <0.1%
- Supported Sample Rate : 44.1, 48, 88.2, and 96 kHz
- Digital Input : 1 x RJ45 Female
- Analog Input : 2 x XLR 3-Pin Female Line Input (Balanced)
- Analog Output : 2 x XLR 3-Pin Male Line Output (Balanced)
- Analog Output : 1 x 1/4" TRS Female Headphone Output (Unbalanced)
- Impedance : Analog Input: ≥10 Kilohms
- Impedance : Headphone Output: ≥16 Ohms
- Input Level : Analog Input: +4/0 dBu (Balanced)
- Output Level : Headphone Output: 20 mW + 20 mW (32 Ohms, 1 kHz, Maximum)
- Level Meters : Display: 2 x 26-Dot LED Meters
- Level Meters : Reference Level: +4/0 dBu (Analog)
- Power Consumption : 10 W
- Power : 100 to 240 VAC, 50/60 Hz
- Dimensions : 19 x 1.7 x 11.2" / 48.2 x 4.4 x 28.4 cm (Including Protruding Parts)
- Weight : 7.7 lb / 3.5 kg
Délai de livraison moyen 2 à 3 jours
Délai de livraison moyen 2 à 3 jours